Search found 34 matches
- Tue Feb 12, 2008 3:31 am
- Forum: The Hangar
- Topic: Rudder Bearings
- Replies: 11
- Views: 24442
Dennis, interesting. I went through the same pain you are experiencing trying to find replacement bearings for the rudder. In the parts manual it looks like it says Fafnir SIK5. I finally found a Fafnir S1K5 and that's the one that fits. There is no dash number involved. I got mine from KAMAN Indust...
- Sat Feb 09, 2008 3:28 am
- Forum: The Hangar
- Topic: Rudder Bearings
- Replies: 11
- Views: 24442
- Fri Nov 09, 2007 3:47 pm
- Forum: The Hangar
- Topic: C-180 Gear
- Replies: 9
- Views: 4604
- Fri Nov 09, 2007 2:56 pm
- Forum: The Hangar
- Topic: C-180 Gear
- Replies: 9
- Views: 4604
- Fri Nov 09, 2007 3:36 am
- Forum: The Hangar
- Topic: C-180 Gear
- Replies: 9
- Views: 4604
C-180 Gear
Does anybody know what the deal is with putting 180/185 gear in a 170B? I know that there is at least one STC to do it, but are there more? What part and/or serial numbers are called out in the STC('s). I know that the early 180 gear was 11/16" and the later ones are 3/4". I would also ima...
- Thu Oct 11, 2007 7:28 pm
- Forum: The Pilot Lounge
- Topic: The New Seaplane/Climb prop thread
- Replies: 54
- Views: 36990
- Fri Sep 07, 2007 9:13 pm
- Forum: The Pilot Lounge
- Topic: engine quits on takeoff - check yer corks
- Replies: 9
- Views: 5654
- Thu Sep 06, 2007 10:27 pm
- Forum: The Pilot Lounge
- Topic: engine quits on takeoff - check yer corks
- Replies: 9
- Views: 5654
- Sun Aug 05, 2007 9:31 pm
- Forum: The Hangar
- Topic: Rudder Pedal Bearings
- Replies: 2
- Views: 2439
Rudder Pedal Bearings
What are you guys using on the rudder pedal bearings (part #s 0411263 and 0411264) for lube? I figured that normal grease or oil would just collect dirt. As I recall, the service manual is fairly vague on the subject.
Thanks
Thanks
- Wed May 02, 2007 10:32 pm
- Forum: The Pilot Lounge
- Topic: Landing on the Ice
- Replies: 17
- Views: 11375
Sorry to change the subject, but here is one for you Fairbanks guys. What is the deal with that 120-140 (not sure) that is sitting on the west side with the rudder removed by the old DC-6's and such. Is that a boneyard or just someone's tiedown. I think there is a straight tail 182 and cherokee over...
- Mon Apr 30, 2007 2:21 am
- Forum: The Hangar
- Topic: Aileron Cables
- Replies: 2
- Views: 2476
Aileron Cables
Any of you guys have any "been there done that" experience changing the aileron control cables from the yoke back. Just looking for tips and/or suggestions to make the job go easier. I have to do both sides.
Thanks
Thanks
- Tue Apr 24, 2007 3:36 am
- Forum: The Hangar
- Topic: Rudder Bearings
- Replies: 6
- Views: 3706
- Sun Apr 22, 2007 10:36 pm
- Forum: The Hangar
- Topic: Fuel Gauges
- Replies: 2
- Views: 2265
Fuel Gauges
I know there have been several posts on the subject, but I couldn't find one with this problem. One of my gauges has been inop, so I took it out. Needle didn't move when I moved the linkage. I thought maybe the needle was corroded/stuck so I took the bezzle and glass apart but the needle moves freel...
- Tue Apr 03, 2007 3:43 am
- Forum: The Hangar
- Topic: Engine mount to engine bushing
- Replies: 1
- Views: 2578
Engine mount to engine bushing
Does anybody know where to get the rubber bushings for the mount to engine interface. Continental part #23411 from the original catalog. I think they are a lord mount, but don't know if the number has been superceded. I imagine somebody out there has a good source for them. Thanks.
- Sun Apr 01, 2007 5:38 pm
- Forum: The Pilot Lounge
- Topic: speed loss on a 80 " prop
- Replies: 8
- Views: 5056
I've got an 8041 prop on mine, and 8.50/6's. It only cruises about 105 mph indicated on these cold days.(45-55F and 2450 rpm). But it sure gets off the ground here at sea level. I'm flying off of gravel so I cant do a static takeoff but at about 1900lbs, it takes less than 500 ft. to get airborne wi...