Search found 59 matches
- Sat Dec 04, 2010 3:45 pm
- Forum: The Pilot Lounge
- Topic: Spark Plug Gap?????
- Replies: 4
- Views: 2974
Re: Spark Plug Gap?????
I am going to order from spruce and shall place a post as to how it works Thanks Bluelder & Bruce
- Fri Dec 03, 2010 3:56 pm
- Forum: The Pilot Lounge
- Topic: Spark Plug Gap?????
- Replies: 4
- Views: 2974
Spark Plug Gap?????
Is there a tool that allows one to OPEN the gap on Champion spark Plugs.. If not any ideas?
- Thu May 20, 2010 6:20 pm
- Forum: The Hangar
- Topic: Tailwheel Spr Retainer item 36,pg49,fig25
- Replies: 9
- Views: 3391
Tailwheel Spr Retainer item 36,pg49,fig25
Help, Help, Help P'ls, Removing and replacing"tailwheel spring retainer" Pt. 0510000-31. Has anyone replaced this part and could help??? How do you acccess the two bolts located fwd on this bracket. AN3-4A. It look. to me that one must crawel thru the fuselage. I'm 6/2" 240 lbs. Have ...
- Sat Jan 02, 2010 6:53 pm
- Forum: The Hangar
- Topic: Looking to overhaul C-145
- Replies: 16
- Views: 9630
Re: Looking to overhaul C-145
I'll second recc on Mattituk. Very professional and at both OSH & Sun N Fun shows. I guess it goes with the saying ya get what you pay for. Bit the bullet, you ''ll feel better every time you go flying.
- Sat Jan 02, 2010 4:24 pm
- Forum: The Hangar
- Topic: Looking to overhaul C-145
- Replies: 16
- Views: 9630
Re: Looking to overhaul C-145
I O/H my own and the cost for parts was close to $11K. This included new thru bolts. All strictly accomplished per Continental O/H manaul. I did however have to replace the case. Only thing over looked was when doing the O/H I should have considered a conversion to a 180.
- Thu Nov 05, 2009 12:03 am
- Forum: The Hangar
- Topic: SNAP RING NEEDED FRO CLEVELAND BRAKES
- Replies: 3
- Views: 1900
Re: SNAP RING NEEDED FRO CLEVELAND BRAKES
SORRY ABOUT THE TYPE O "SNAP RING NEEDED [b]FOR [/b]CLEVELAND BRAKES
- Thu Nov 05, 2009 12:01 am
- Forum: The Hangar
- Topic: SNAP RING NEEDED FRO CLEVELAND BRAKES
- Replies: 3
- Views: 1900
SNAP RING NEEDED FRO CLEVELAND BRAKES
IN THE SERVICE MANUAL PG 5-14 I AM IN NEED OF TWO "SNAP RINGS, ITEM 15. ALSO IN THIS MANUAL I SEE ITEM 17 WHICH I WOULD CONSIDER A GREASE SEAL. Yes I do see item 18. WHAT I ALSO NEED IS THE THE COLLAR ITEM 17. CAN ANYONE STRAIGHTEN ME OUT? I NEED THE LAST PART PRIOR TO THE AXLE NUT ALSO. WHAT E...
- Tue Aug 18, 2009 2:19 pm
- Forum: The Pilot Lounge
- Topic: Gaston's Resort
- Replies: 18
- Views: 21926
Re: Gaston's Resort
I see where a few of you guys/gals are takling about "Gastons" I beg of ya to take a look at the Events section for flying at Rough River, Lee Bottom and Welcome Field
- Mon Jun 23, 2008 1:17 pm
- Forum: The Pilot Lounge
- Topic: Tailwheel spring clamp
- Replies: 16
- Views: 34372
Re: Tailwheel spring clamp
Speakiing of part number fig 29. , Index -8, 0510000-31. Can anyone tell me if this part can be replaced w/o vertical fin removal. This is what the guys told me at the Sun N Fun 170 seminar. " I needed to remove the vertical fin to get at the two bolts facing forward towards the nose of the acf...
- Sat Jan 05, 2008 5:53 pm
- Forum: The Pilot Lounge
- Topic: Indiana Fly-In
- Replies: 10
- Views: 5409
170 Lee Bottom
I'm in and shall try for a few more.
Fred
N8109A
Fred
N8109A
- Sun Dec 30, 2007 5:51 pm
- Forum: The Hangar
- Topic: Door Seal
- Replies: 52
- Views: 149912
Door Seals
I too have recently replaced the seal on my passanger door. I used the one supplied by Bill Rhoades, PO box 51, Northfield, MN 55057. The product is the original style used on 120/140. I purchased 25 ft. (cost $31.25) and followed his instructions. I bet I put 15 hours in removing the door and then ...
- Sun Oct 14, 2007 2:07 pm
- Forum: The Pilot Lounge
- Topic: LOOKING FOR GREG HOWARD last noted location ARK.
- Replies: 4
- Views: 3131
LOOKING FOR GREG HOWARD last noted location ARK.
Does anyone have any information on how Mr. Greg Howard could be located. I understand that he last lived in ARK and had a couple of 170"s, also past member?
FRED
FRED
- Wed Aug 29, 2007 2:16 pm
- Forum: The Hangar
- Topic: Engine name plate?
- Replies: 3
- Views: 2682
Date Plate
Guess I'll take george's advice and just keep the old one. Thanks Geo.
- Mon Aug 27, 2007 7:56 pm
- Forum: The Hangar
- Topic: Engine name plate?
- Replies: 3
- Views: 2682
Engine name plate?
I have a engine name plate that has only the embossed numbers left. I thought that I would go ahead and get a new one. I received FSDO approval at which time I contacted Continential. for a new plate they request $100.00 Yes!!!!! One hundered. Any comments?
- Tue Aug 21, 2007 11:25 pm
- Forum: The Hangar
- Topic: Door Seals
- Replies: 1
- Views: 1848
Door Seals
I am sure this has been discussed before. Can ya tell me where to find out 170 input for the replacement of doors seals? By the way my broken door latch has been repaired THANKS to John Barrett. Thanks again John