Recommended Modifications/Repairs for 170 Owners

How to keep the Cessna 170 flying and airworthy.

Moderators: GAHorn, Karl Towle, Bruce Fenstermacher

User avatar
Bruce Fenstermacher
Posts: 10313
Joined: Tue Apr 23, 2002 11:24 am

Re: Recommended Modifications/Repairs for 170 Owners

Post by Bruce Fenstermacher »

At the same time you replace the main leaf spring, replace the AN7-20A bolt that attaches the tail wheel to the main spring. This one lasted at least 17 years with an average of 50 hours a year and one landing per hour that's 850 hours/landings. If it breaks on landing it WILL ruin your day.
Photo on 2010-07-01 at 15.57.jpg
Photo on 2010-07-01 at 15.57.jpg (77.72 KiB) Viewed 95112 times
CAUTION - My forum posts may be worth what you paid for them!

Bruce Fenstermacher, Past President, TIC170A
Email: brucefenster at gmail.com
User avatar
GAHorn
Posts: 20967
Joined: Fri Apr 12, 2002 8:45 pm

Re: Recommended Modifications/Repairs for 170 Owners

Post by GAHorn »

N9149A wrote:At the same time you replace the main leaf spring, replace the AN7-20A bolt that attaches the tail wheel to the main spring. This one lasted at least 17 years with an average of 50 hours a year and one landing per hour that's 850 hours/landings. If it breaks on landing it WILL ruin your day.
Photo on 2010-07-01 at 15.57.jpg
EXTREMELY fortunate you were taxying slowly and on grass. When this breaks on takeoff or (more likely) on landing...the tailwheel flails the rudder to smithereens....adding considerable to the cost and trouble.
'53 B-model N146YS SN:25713
50th Anniversary of Flight Model. Winner-Best Original 170B, 100th Anniversary of Flight Convention.
An originality nut (mostly) for the right reasons. ;)
User avatar
Romeo Tango
Posts: 74
Joined: Tue Sep 02, 2003 10:32 pm

Re: Recommended Modifications/Repairs for 170 Owners

Post by Romeo Tango »

Heading into the annual, so I revisited this wonderful post to check on the entries and any new updates. All good stuff, thank you for the contributions. I've put in two items over the years that are worth mentioning.

a) Mixture cable/control replacement. The mixture control installed when I bought the airplane (original as far as I know) was a gimpy push/pull deal that always felt like it had the potential to fall apart when used. It was also an adventure to lean the engine properly without 500RPM gyrations. I fly at 10-12K quite often and leaning is pretty important. The McFarlane replacement is solid and has a twist vernier control for fine tuning.

b) control cable replacement with new galvanized modern equivalents (McFarlane again). I had a flap cable fail on a preflight, so I decided to replace all cables at the next annual, including all of the hardware. Cost out the door was <$1500 plus labor. If you are replacing fabric, repainting or otherwise have the airplane torn apart, this is a very good insurance policy against the inflight failure that would make for a lot of paperwork. Plus the act of going through this much rerigging will force your AP to dig deeply into nooks and crannies and find those elusive corrosion spots.
User avatar
KG
Posts: 493
Joined: Thu Feb 09, 2006 5:14 pm

Re: Recommended Modifications/Repairs for 170 Owners

Post by KG »

Regarding using the L19 eye bolt on the tailwheel (item 14 on the first post of this thread), use the nylon locknut with caution. See this post with information about the nylon locknut:
http://www.cessna170.org/forums/viewtop ... f=2&t=7845

short version --- replace the nylon locknut with a steel locknut.

edit: the last L19 eye bolt that I bought did not come with a locknut, nylon or otherwise. So you'll have to supply your own steel locknut. The price of the bolt had also gone up considerably. I doubt if I would buy another one as it was over $40 delivered.
53 170B
User avatar
architect1
Posts: 15
Joined: Wed Mar 14, 2012 6:57 am

Re: Recommended Modifications/Repairs for 170 Owners

Post by architect1 »

I use the True-Lock axle nut with my straight skis to keep the axle shaft open for my dolly's. They work fine.
1952 C170B
User avatar
gfeher
Posts: 571
Joined: Fri Sep 26, 2014 9:19 pm

Re: Recommended Modifications/Repairs for 170 Owners

Post by gfeher »

It appears that the L-19 tail wheel eye bolt has come back down in price. I just purchased and received one from Air Repair for $21 plus postage. Not the cheapest bolt you can purchase, but less than the $40 someone mentioned it was going for a few years ago.
Gene Feher
Argyle (1C3), NY
'52 170B N2315D s/n 20467 C-145-2
Experimental J3 Cub Copy N7GW O-200
User avatar
GAHorn
Posts: 20967
Joined: Fri Apr 12, 2002 8:45 pm

Re: Recommended Modifications/Repairs for 170 Owners

Post by GAHorn »

KG wrote:Regarding using the L19 eye bolt on the tailwheel (item 14 on the first post of this thread), use the nylon locknut with caution. See this post with information about the nylon locknut:
http://www.cessna170.org/forums/viewtop ... f=2&t=7845

short version --- replace the nylon locknut with a steel locknut.

edit: the last L19 eye bolt that I bought did not come with a locknut, nylon or otherwise. So you'll have to supply your own steel locknut. The price of the bolt had also gone up considerably. I doubt if I would buy another one as it was over $40 delivered.
BE CERTAIN of the grip-length of the eyebolt versus the thickness of your tailsprings. The L-19 eyebolt was intended for the thicker L-19 mainspring and when used on the 170 mainspring might be a bit too long in the grip, requiring at least one, and maybe two addt'l flat washers in order to guarantee that the lock-nut used does not "bottom-out"...and will retain it's proper torque.
'53 B-model N146YS SN:25713
50th Anniversary of Flight Model. Winner-Best Original 170B, 100th Anniversary of Flight Convention.
An originality nut (mostly) for the right reasons. ;)
User avatar
thanatos767
Posts: 3
Joined: Fri Jan 24, 2020 3:48 am

Re: Recommended Modifications/Repairs for 170 Owners

Post by thanatos767 »

Has anyone installed shoulder belts in a 170A?
Chris Smith
1951 170A, N1250D, s/n 20122
Owner as of 02/1/2020
hilltop170
Posts: 3481
Joined: Sat May 06, 2006 6:05 pm

Re: Recommended Modifications/Repairs for 170 Owners

Post by hilltop170 »

I had the BAS lap belt and shoulder harness conversion installed in my 170A. Nut plates were installed overhead in the rear spar carry-thru which is detailed in other threads in the Forums.

I got the version that has tabs on the shoulder belts that assemble onto the lap belt tab and come completely apart when released and adjusters on both sides of the seat belts.
BAS seat belts/shoulder harnesses with full-release latches and adjusters on both sides of seat belts
BAS seat belts/shoulder harnesses with full-release latches and adjusters on both sides of seat belts
Shoulder harness bracket attach points, 4 bolts shown along front rivet line on rear spar carry-thru replacing existing rivets
Shoulder harness bracket attach points, 4 bolts shown along front rivet line on rear spar carry-thru replacing existing rivets
Last edited by hilltop170 on Wed Jan 20, 2021 9:34 pm, edited 1 time in total.
Richard Pulley
2014-2016 TIC170A Past President
1951 170A, N1715D, s/n 20158, O-300D
Owned from 1973 to 1984.
Bought again in 2006 after 22 years.
It's not for sale!
User avatar
ghostflyer
Posts: 1390
Joined: Mon Apr 21, 2008 3:06 am

Re: Recommended Modifications/Repairs for 170 Owners

Post by ghostflyer »

Richard,
Did you use a STC instruction sheet from the manufacturer of the belts For the installation. I have gone down the same path as you with the belts but I went to Cessna for advice And/ or a authorised drawing .
I had to place and seal a plate on top of my roof of the fuselage , a plate of 36thou of 7075 -T6 . I had to proseal the plate to the top of the skin externally. It was a messy job with proseal dripping through the rivet holes . I had proseal in my armpits , in my beard ,but not in my hair as I haven’t any. I could send you a copy of the modification for your comment but I have placed it in a safe place and I can’t remember where it was. Cessna went on also in that information sheet about corrosion that could be present in the hat section. This area was in very good condition on my aircraft but we made a probe with fine holes in it attached it to a spray gun and painted internally The hat section with zinc chromeate .
User avatar
gobrien
Posts: 113
Joined: Sun May 19, 2019 11:36 am

Re: Recommended Modifications/Repairs for 170 Owners

Post by gobrien »

14. Install an L19 tailwheel tie-down eyebolt (PN 0642105) in lieu of the AN7-22A bolt that holds your tailwheel assy to the main leafspring.
Gents,

I have looked in the 170 IPC Fig 20 and 170B IPC Fig 27 and 28 (in case it changed later) and in both cases the tailwheel assembly is attached to the main leaf spring with an AN7-10A. I see references in various articles to the above mentioned AN7-22A. Was there an AD or SB or something that I'm missing that changed the -10A to a -22A?

Thanks,

Gareth
1948 170 Project (N4180V) now EI-AEN SN:18513 - Dublin, Ireland
https://www.taildragger.eu/
User avatar
170C
Posts: 3182
Joined: Tue May 06, 2003 11:59 am

Re: Recommended Modifications/Repairs for 170 Owners

Post by 170C »

Comment & Question I may be repeating myself on this, but I originally purchased an L-19 tailwheel bolt from Air Repair, Inc in Cleveland, MS back in July of 2004 when George brought this item to the association's attention. It worked well for many years, but eventually I noticed the bolt was turning 10-20 degs. I would tighten the nut, but the problem would return. I believe it was George who suggested a torque of 50-60 lbs which I used, but the problem persisted. This past October (2019) I purchased a new bolt (P#0642105) and installed it using Nord-Lock Wedge Locking washers and a steel nut. To date I have not had any further issues with the bolt moving.
My question - With the installation of the tail wheel springs, does anyone put any kind of material (baffeling or otherwise) under the springs in the spring channel?
OLE POKEY
170C
Director:
2012-2018
User avatar
gfeher
Posts: 571
Joined: Fri Sep 26, 2014 9:19 pm

Re: Recommended Modifications/Repairs for 170 Owners

Post by gfeher »

Gareth, many (likely most) C-170's now have a Scott tailwheel, and a longer AN7 bolt is needed for that tailwheel. The figures you mention from the IPC show the original tailwheel. Fig 98 of the 170B IPC, for example, shows the "optional" Scott tailwheel version, and you'll notice the bolt listed is an AN7-20A, which is what I have on my plane with a Scott tail wheel. I'm not sure why the post you quoted refers to a little longer -22A bolt, other than to say that in the US, an A&P can exercise some descretion when choosing a bolt length within the limitations/requirements of AC43.13-1b, such as the number of threads that must show and the maximum number of washers you may use. On my plane, the -20 length works. By the way, in the US, the IPC's are not regulatory. Although they are extremely helpful in determining what's on the aircraft, ultimately they are just catalogs for ordering parts. Also, they do contain errors,
Gene Feher
Argyle (1C3), NY
'52 170B N2315D s/n 20467 C-145-2
Experimental J3 Cub Copy N7GW O-200
User avatar
dstates
Posts: 472
Joined: Sun Jun 30, 2019 5:50 pm

Re: Recommended Modifications/Repairs for 170 Owners

Post by dstates »

I ordered a L-19 tailwheel bolt without fully doing the research. I have a Maule tailwheel and it will not work with a Maule.
N1235D - 1951 170A - SN: 20118
User avatar
gobrien
Posts: 113
Joined: Sun May 19, 2019 11:36 am

Re: Recommended Modifications/Repairs for 170 Owners

Post by gobrien »

Thanks Gene,

That makes sense. I have become familiar with mistakes in the IPC! :?

Gareth
1948 170 Project (N4180V) now EI-AEN SN:18513 - Dublin, Ireland
https://www.taildragger.eu/
Post Reply