Fuse holder

OTIS · Post by **OTIS** » Tue Sep 22, 2015 5:28 pm

I had one of my fuse holders break and need a replacement. The part # is 0411023-1 (Retainer - Fuse)
Does anyone have an extra they want to sell or now where I can buy one?

Gerry Whitson
N8072A

blueldr · Post by **blueldr** » Tue Sep 22, 2015 7:15 pm

I have two fuse holders sitting here on my desk i front of me. One for a 5/16" dia, fuse the other for a 1/4" dia.

Send me a couple of bucks for postage and they're yours.

Dick Lemmon
2469 Knightwood Way
Rancho Cordova, CA 95670-5104
Ph. (916) 635-5566

OTIS · Post by **OTIS** » Thu Sep 24, 2015 11:41 am

Thank you Dick. I'll mail you a $10 check today.

Gerry Whitson
311 Meadow Lake Drive
Taylorsville, KY. 40071

blueldr · Post by **blueldr** » Thu Sep 24, 2015 3:48 pm

Gerry,
Thanks for the offer but I don;t want to sell the fuseholders. I'm just going to loan them to tou on a permanent basis. All I want is postage, thank you.

D ick

OTIS · Post by **OTIS** » Sun Oct 04, 2015 3:32 am

Thanks again. Did you receive an envelope from me last week?

Gerry

blueldr · Post by **blueldr** » Sun Oct 04, 2015 6:54 pm

Gerry,

I've received nothing at all so far.

Dick

OTIS · Post by **OTIS** » Thu Oct 08, 2015 1:41 pm

Dick, I mailed the postage check yesterday. Gerry

blueldr · Post by **blueldr** » Thu Oct 08, 2015 4:12 pm

I'll be watching the mail for it. Thanks.

Post by **GAHorn** » Sat Oct 10, 2015 2:45 am

Been drinkin' that Kain-tucky Hooch agin' , Gerry...??? (an' fergot to mail the chek?)

OTIS · Post by **OTIS** » Sat Nov 07, 2015 8:24 pm

George........yes on local hooch.

I'm still looking for a fuse cap. Dick sent me a complete fuse assembly. Unfortunately, it uses a different type cap. A
I took a picture, but it is to large to upload. My fuse cap is 1 1/8 inches long and screws into the fuse holder. Not sure
Where to go from here.

Gerry
N8072A

n3833v · Post by **n3833v** » Sat Nov 07, 2015 10:44 pm

Gerry,
I think I have what you need. The screw part is 1.25 in long with the knerl knob is .5 in with fuse printed on the end for a .25 fuse.

John

OTIS · Post by **OTIS** » Mon Nov 16, 2015 8:46 pm

John, I received your package today. It was the correct part. Thank you very much. Gerry

n3833v · Post by **n3833v** » Tue Nov 17, 2015 12:34 pm

You are welcome. Now I hope you fly safely with the extra unit working. This was from when I changed my panel to all breakers for my IFR panel.

John

The International Cessna^® 170 Association

Fuse holder

Fuse holder

Re: Fuse holder

Re: Fuse holder

Re: Fuse holder

Re: Fuse holder

Re: Fuse holder

Re: Fuse holder

Re: Fuse holder

Re: Fuse holder

Re: Fuse holder - second try

Re: Fuse holder

Re: Fuse holder

Re: Fuse holder