I'm looking for one Flap Stop bolt p/n 0523214. I've tried Preferred Airparts and Cessna Parts.com and no one has them. Are they just an long AN bolt that I can find in stock or is it a Cessna part? Anyone have any other parts places? I think there's a post here somewhere that has all those places listed, I'll try to find it.
thanks!
Jud
Need Bolt
Moderators: GAHorn, Karl Towle, Bruce Fenstermacher
-
mongo2
- Posts: 99
- Joined: Thu Nov 02, 2006 11:42 pm
Re: Need Bolt
I'm trying to locate a cross reference as well. Does anyone know of any? I don't have any of the original ones to measure...
RC
RC
Rick Champagne
C-170A N5475C
C-170A N5475C
-
Bruce Fenstermacher
- Posts: 10423
- Joined: Tue Apr 23, 2002 11:24 am
Re: Need Bolt
#32 in this drawing from the A model IPC
You do not have the required permissions to view the files attached to this post.
CAUTION - My forum posts may be worth what you paid for them!
Bruce Fenstermacher, Past President, TIC170A
Email: brucefenster at gmail.com
Bruce Fenstermacher, Past President, TIC170A
Email: brucefenster at gmail.com
-
hilltop170
- Posts: 3485
- Joined: Sat May 06, 2006 6:05 pm
Re: Need Bolt
Judd and RC-
If it's on an A Model, I'll measure mine when I get home on Tuesday.
If it's on an A Model, I'll measure mine when I get home on Tuesday.
Richard Pulley
2014-2016 TIC170A Past President
1951 170A, N1715D, s/n 20158, O-300D
2023 Best Original 170A at Sault Ste. Marie
Owned from 1973 to 1984.
Bought again in 2006 after 22 years.
It's not for sale!
2014-2016 TIC170A Past President
1951 170A, N1715D, s/n 20158, O-300D
2023 Best Original 170A at Sault Ste. Marie
Owned from 1973 to 1984.
Bought again in 2006 after 22 years.
It's not for sale!
-
blueldr
- Posts: 4442
- Joined: Thu May 02, 2002 3:16 am
Re: Need Bolt
From the picture above, it would appear to me that there must be four of these bolts per airplane. Your request has you looking for one only. Do you have any others to measure for identification?
BL
-
edbooth
- Posts: 498
- Joined: Wed Nov 24, 2004 3:03 am
Re: Need Bolt
Don't think they have these on a "B" model. Don't know about the straight 170.hilltop170 wrote:Judd and RC-
If it's on an A Model, I'll measure mine when I get home on Tuesday.
Ed Booth, 170-B and RV-7 Driver
-
mongo2
- Posts: 99
- Joined: Thu Nov 02, 2006 11:42 pm
Re: Need Bolt
Gentlemen,
The drawing is correct. A model. 4 bolts needed.......
I'm going to check another PN source in the meanwhile.......
Thank you
RC
The drawing is correct. A model. 4 bolts needed.......
I'm going to check another PN source in the meanwhile.......
Thank you
RC
Rick Champagne
C-170A N5475C
C-170A N5475C
-
ghostflyer
- Posts: 1423
- Joined: Mon Apr 21, 2008 3:06 am
Re: Need Bolt
I needed 3 when reassembling [ rebuilding] my aircraft and couldn't get the part from Cessna or its agent here in OZ but so I measured it and ordered it [ AN bolt] from Spruce. not very expensive at all. they ended up in sending the MS equivalent.
however the bolts that attach the vertical fin to the tail plane [NAS 145-14 and 18] , Cessna wanted nearly $800 dollars for them. This stopped the original owners of the aircraft [it was in a thousand pieces] from starting the rebuild. Some of the hardware required that was needed gave the original owners [a gliding club committee] ticket shock. I found a supplier down in the south of the country that had dozens of -14,s but he requested that I purchase them at 6 per time at the grand cost of $9 per 6. they came with the correct paper work . I gave him $10 bucks and told him he could keep the change. The moral of this story is to shop around . If the correct paper work comes with the hardware and its from a reliable source ,think about using it.
however the bolts that attach the vertical fin to the tail plane [NAS 145-14 and 18] , Cessna wanted nearly $800 dollars for them. This stopped the original owners of the aircraft [it was in a thousand pieces] from starting the rebuild. Some of the hardware required that was needed gave the original owners [a gliding club committee] ticket shock. I found a supplier down in the south of the country that had dozens of -14,s but he requested that I purchase them at 6 per time at the grand cost of $9 per 6. they came with the correct paper work . I gave him $10 bucks and told him he could keep the change. The moral of this story is to shop around . If the correct paper work comes with the hardware and its from a reliable source ,think about using it.
-
mongo2
- Posts: 99
- Joined: Thu Nov 02, 2006 11:42 pm
Re: Need Bolt
Would you happen to remember what number AN bolts you ordered or MS equivalent they sent you were?
RC
RC
Rick Champagne
C-170A N5475C
C-170A N5475C
-
wingnut
- Posts: 990
- Joined: Fri Dec 15, 2006 7:58 pm
Re: Need Bolt
Your 0523214 bolts have been replaced with AN3-16A flap stop bolt. At least that what they were when we removed the old ones. If they are something special, you don't have special. You just have functionalhilltop170 wrote:Judd and RC-
If it's on an A Model, I'll measure mine when I get home on Tuesday.
Del Lehmann
Mena, Arkansas
Mena, Arkansas
Cessna® is a registered trademark of Textron Aviation, Inc. The International Cessna® 170 Association is an independent owners/operators association dedicated to C170 aircraft and early O-300-powered C172s. We are not affiliated with Cessna® or Textron Aviation, Inc. in any way.